Shadow Dexterous Hand Extra Lite (DHEL)
In stock
- BRAND:
- SHADOW ROBOT
- PART #:
- DHEL
- AVAILABILITY:
- SUBJECT TO AVAILABILITY
- SKU:
- Shadow-DHEL
Shadow Dexterous Hand Extra Lite (DHEL)
Every gram at the end of a robot arm is a gram the arm must lift, accelerate and bring to rest, and every extra finger is another motor to calibrate, another tendon to tension and another data stream to log. The Shadow Dexterous Hand Extra Lite (DHEL) responds to that pressure by keeping the part of the human hand that most grasping work relies on, a thumb working against two fingers, while carrying over the sensing and control architecture of Shadow's larger hands. It is an advanced humanoid robot hand system designed to reproduce as closely as possible the kinematics and dexterity of the human hand, built around 10 DOF across 12 joints and driven by 10 DC motors.
Robots Middle East supplies the Shadow Dexterous Hand Extra Lite (DHEL) to universities, research institutes and industrial laboratories across the Middle East. Each quotation is prepared against the configuration you require, whether a right or left hand, the number of tactile fingertips, or a hand delivered integrated with a UR5 or UR10 robot arm, and Robots Middle East remains your point of contact for delivery, commissioning questions and continuing support.
Background
Shadow Robot and the Dexterous Hand family
Shadow Robot is a British robotics company whose name has long been tied to anthropomorphic robot hands. Its Dexterous Hand is offered in four versions: the Shadow Dexterous Hand, the Lite, the Extra Lite and the Super Lite. They differ in the number of fingers and actuated joints, yet they share one technical backbone. Every version uses an EtherCAT bus, runs a 1kHz control loop through the host and carries an inertial measurement unit. The hand has been used in established research systems such as Willow Garage's PR2 robot, which makes it compatible with the PR2 and with other EtherCAT and ROS compatible research or industrial control systems. For a laboratory, this means that the Extra Lite does not sit in a separate software world: code, tools and experience gained on one Shadow hand carry over to another.
Sensing at the tendon and at the joint
What distinguishes the Extra Lite from a simple gripper is the density of information it returns. A Hall effect sensor senses the rotation of each joint locally, with a typical resolution of 0.2 degrees. Twenty tendon load sensors, each with a resolution of about 30mN, report how hard the drive tendons are pulling. The torque loop is closed inside the motor unit at 5kHz, while the host runs its own loop at 1kHz over EtherCAT. One Shadow Tactile Fingertip is fitted as standard, and the hand accepts up to three. The result is a hand that can be controlled by force as well as by position, and whose every grasp leaves a detailed record for later analysis.
Technical Specifications
| Specification | Value |
|---|---|
| Degrees of freedom | 10 DOF across 12 joints |
| Number of fingers | 2 + 1 (thumb) |
| Number of actuators | 10 DC motors |
| Shadow Tactile Fingertips (STFs) fitted as standard | 1 |
| Maximum number of STFs | 3 |
| Tendon load sensors | 20 |
| Tendon force sensor resolution | About 30mN |
| Joint position sensing | Hall effect sensor at each joint, typical resolution 0.2 degrees |
| Inertial measurement units (IMU) | 1 |
| Torque loop | Closed inside the motor unit at 5kHz |
| Control loop rate through host | 1kHz (EtherCat protocol) |
| Communications bus | EtherCAT, 100Mbps Ethernet-based communications field-bus, full integration into ROS |
| Movement speed | Full-range joint movement in free space at a frequency of 1.0 Hz (typical parameters) |
| Power-grasp payload | Up to 3 Kg |
| Overall weight (series specification) | 2.1 Kg |
| Hand and forearm weight (technical specification) | 1.8 kg |
| Power supply provided | 24 V @ 2.5 A |
| Materials | Aluminium, brass, acetyl, polycarbonate and polyurethane flesh |
| Robot arm integration | Optional, with a UR5 or UR10 robot arm |
| Hand orientation | Standard Hand or Left Hand (mirrored, functionally identical) |
Specifications are as published by the manufacturer and are confirmed against the datasheet at quotation.
The manufacturer has not published the dimensions, the IP rating, the operating temperature range, the fingertip force, the service life, the operating voltage range or the total number of tactile sensors; these are confirmed at quotation.
What does the Extra Lite give up compared with the Lite and the full Hand?
The answer is fingers and actuated joints, not the quality of control. The full Shadow Dexterous Hand has four fingers and a thumb, 20 DC motors and 20 actuated DOF with a further 4 under-actuated movements, for a total of 24 joints. The Lite steps down to three fingers and a thumb, with 13 DOF across 16 joints. The Extra Lite goes further, to two fingers and a thumb with 10 DOF across 12 joints, and the Super Lite reduces the hand to a single finger opposed by the thumb, with 7 DOF across 8 joints.
What does not change across that range is the architecture beneath the fingers. The Extra Lite keeps the same EtherCAT bus, the same 1kHz host control loop and the same inertial measurement unit as its larger siblings, together with tendon load sensing and local joint sensing. A laboratory therefore loses hand geometry, not signal quality. Shadow cites a 35% power saving when moving from the five-fingered Hand to the four-fingered Lite; no equivalent figure is published for the Extra Lite, so the energy benefit of the further reduction should be discussed at quotation rather than assumed.
For many grasping tasks, a thumb opposed to two fingers is enough to form pinch, tripod and power grasps, and the Extra Lite can hold up to 3 Kg in a power-grasp. Research that depends on the coordination of four separate fingers, or on in-hand manipulation that uses the whole human finger set, is better served by a larger version.
How does the Extra Lite fit into an existing robot cell?
Integration is where the shared architecture pays off. The hand communicates over EtherCAT, a 100Mbps Ethernet-based field-bus, with full integration into ROS, so it can be brought into existing ROS workspaces rather than requiring a proprietary control stack. Its compatibility with the PR2 and with other EtherCAT and ROS compatible systems widens the range of platforms it can join.
For teams that would rather not build their own mounting and control layer, the Dexterous Hand system can be supplied integrated with a UR5 or UR10 robot arm. A Left Hand is available as well; it is functionally identical to the standard Hand but mirrored, which allows two hands to work together in a bi-manual system.
The development kit is intended to make the hand usable from the first day. It includes control systems, software released under GNU GPL or BSD as appropriate, ROS compliance, a PC, power supplies, tactile sensing, auxiliary equipment where required, documentation and training. The supplied power supply is rated at 24 V @ 2.5 A.
Who is the Shadow Dexterous Hand Extra Lite (DHEL) for?
The Extra Lite suits university laboratories and research institutes that study grasping, force control and tactile perception and want an anthropomorphic hand without the mechanical scope of a five-fingered system. Groups building bi-manual platforms will value the mirrored Left Hand, and industrial research and development teams exploring dexterous manipulation on collaborative arms can take advantage of integration with a UR5 or UR10. Because the hand shares its software and bus with the other Shadow hands, it also suits organisations that expect to grow into a larger hand later.
Where your research calls for a fuller finger set, the Shadow Dexterous Hand Lite (DHL) adds a third finger, and the Shadow Dexterous Hand (DH) offers four fingers and a thumb for work that aims at full human-hand dexterity. If the task needs only a thumb opposed to one finger, the Shadow Dexterous Hand Extra Super Lite (DHSL) is the more compact choice. The wider range is presented under Robot Hands and Shadow Robot.
What is the Shadow Dexterous Hand Extra Lite (DHEL) used for?
- Grasp research: studying pinch, tripod and power grasps with a thumb opposed to two fingers.
- Tactile sensing studies: recording contact data from Shadow Tactile Fingertips alongside joint and tendon signals.
- Force-controlled manipulation: developing controllers that use tendon load sensing and the fast inner torque loop.
- Bi-manual systems: pairing a standard Hand with a mirrored Left Hand for two-handed tasks.
- Arm-mounted manipulation: combining the hand with a UR5 or UR10 robot arm for reach-and-grasp experiments.
- Teaching and training: giving students hands-on experience of ROS-based dexterous control on a manageable platform.
Pricing and Availability
Robots Middle East prepares a formal quotation for each configuration, taking into account the hand orientation, the number of tactile fingertips and any robot arm integration you require. Delivery, customs clearance and support are arranged together with the quotation. We would be pleased to discuss your project and its technical requirements before you commit. To begin, a quotation request for the Shadow Dexterous Hand Extra Lite (DHEL) is available on this page.
Frequently Asked Questions
How many fingers does the Shadow Dexterous Hand Extra Lite have?
The hand has two fingers and a thumb, with 10 DOF across 12 joints driven by 10 DC motors.
Can the hand be mounted on a robot arm?
Yes. The Dexterous Hand system can be supplied integrated with a UR5 or UR10 robot arm.
Does the Extra Lite work with ROS?
Yes. It uses an EtherCAT bus with full integration into ROS and is compatible with the PR2 and other EtherCAT and ROS compatible control systems.
Is a left-hand version available?
Yes. The Left Hand is functionally identical to the standard Hand but mirrored, for use in a bi-manual system.
How many tactile fingertips does it have?
One Shadow Tactile Fingertip is fitted as standard, and the hand accepts up to three.
What does the development kit include?
It includes control systems, software under GNU GPL or BSD as appropriate, ROS compliance, a PC, power supplies, tactile sensing, auxiliary equipment where required, documentation and training.
Where can I buy the Shadow Dexterous Hand Extra Lite (DHEL) and what does it cost?
The hand is available from Robots Middle East, which supplies it across the Middle East. The cost depends on the configuration you choose and is set out in a formal quotation that you can request from this page.
Summary
The Extra Lite is Shadow's answer to the weight and complexity that accumulate at the end of a robot arm. By keeping a thumb against two fingers and retaining tendon load sensing, local joint sensing, a 5kHz torque loop and EtherCAT control with ROS integration, it offers a laboratory a dexterous hand that is easier to mount, run and interpret than a full five-fingered system, without abandoning the shared architecture of the family. Arm integration, a mirrored Left Hand and a complete development kit make it ready for serious research from the outset. For laboratories in the Middle East planning their next manipulation platform with Robots Middle East, this page is the starting point.