Inspire Dexterous Left Hand (RH56F1-E2L)

An all-metal dexterous left hand from INSPIRE ROBOTS for humanoid platforms, research arms and manipulation studies that call for a firm grasp with finely regulated force. Robots Middle East supplies it to laboratories and integrators across the region, with the configuration agreed at quotation.

In stock

BRAND:
INSPIRE ROBOTS
PART #:
RH56F1-E2L
ORIGIN:
China
AVAILABILITY:
SUBJECT TO AVAILABILITY
SKU:
Inspire-RH56F1-E2L
AED 17,022.06
Free Shipping
Loading...

Inspire Dexterous Left Hand (RH56F1-E2L)

In a robot cell, the bottleneck is seldom the motor. It is the message: how quickly a controller learns what a finger has met, and how quickly the correction travels back to the joint. The Inspire Dexterous Left Hand (RH56F1-E2L) is built around that exchange. It communicates with its host over EtherCAT and RS485 at a communication frequency of 1 kHz, resolves force in steps of 0.1N and repeats a position to ±0.2mm, so the grasp a programme commands and the grasp the hand delivers remain closely matched. Behind that responsiveness stands an all-metal hand with an integrated skeleton, six degrees of freedom distributed across twelve joints, and a structure that holds a static passive load of 30 kg.

Robots Middle East supplies the Inspire Dexterous Left Hand (RH56F1-E2L) to universities, research centres, system integrators and industrial development teams across the Middle East. Our team prepares each quotation for the exact configuration you require, arranges delivery to your site and remains your point of contact for technical support once the hand is in service.

Background

INSPIRE ROBOTS and the RH56F1 line

INSPIRE ROBOTS develops dexterous robotic hands for humanoid platforms, robotic arms and manipulation research, and the RH56F1 is one of the lines it offers within the wider Inspire Robots range. The manufacturer sums up the design intent in a single phrase: refined structure, sensitive perception and stable manipulation. Those three ideas map neatly onto the figures. The structure is all-metal with an integrated skeleton; perception shows in the fine force resolution; and stability is expressed through repeatability and a short hand closing time.

The RH56F1 is offered in four configurations. There are left and right hands, and each side is available with one of two interface pairings: EtherCAT with RS485 (the E2 variants) or EtherCAT with CAN FD (the E4 variants). The product on this page, the RH56F1-E2L, is the left hand with EtherCAT and RS485. Its siblings are the RH56F1-E4L, the RH56F1-E2R and the RH56F1-E4R.

Why the interface pairing matters

For a dexterous hand, the communication bus is not a minor detail; it determines how easily the hand slots into the rest of the system. EtherCAT is widely adopted in industrial motion control, where deterministic timing between a master controller and many devices is essential. RS485 is a robust and familiar serial standard, frequently chosen for bench testing, laboratory rigs and simpler controllers. CAN FD, offered on the E4 variants, is common in robotic and vehicle-derived architectures where many nodes share one network.

By pairing EtherCAT with RS485, the E2L gives a team two routes into the hand: a high-performance industrial link for the finished robot, and a straightforward serial link that suits early development, diagnostics and test benches. Choosing between the E2 and E4 variants is therefore largely a question of which bus your controller and wider architecture already use.

Technical Specifications

SpecificationValue
Hand sideLeft
Communication interfaceEtherCAT + RS485
Degrees of freedom6
Number of joints12
Weight630g ±10g (with tactile)
Operating voltage24V–48V
Communication frequency1 kHz
Repeatability±0.2mm
Thumb fingertip force≥15N
Finger fingertip force≥10N
Force resolution0.1N
Static passive load30 kg
Hand closing time≤0.8s
Body constructionAll-metal, integrated skeleton
In the boxOne RH56F1 hand in the ordered configuration; mounting adapters, controller, power supply and cables are not included unless itemised in the order

Specifications are as published by the manufacturer and are confirmed against the datasheet at quotation.

The manufacturer has not published the IP rating, the operating temperature range, the payload, details of the software SDK, the fingertip speed, the service life or the cable length; each of these is confirmed at quotation.

What is the difference between the RH56F1-E2L and the RH56F1-E4L?

Both are left hands from the same RH56F1 line, and the mechanical and force figures are given for the RH56F1 series as a whole rather than for an individual variant. What separates them is the second interface. The RH56F1-E2L combines EtherCAT with RS485, whereas the RH56F1-E4L combines EtherCAT with CAN FD.

In practice, the decision follows your controller. A laboratory that develops and tests on a workstation with a serial adapter, or that already runs RS485 devices, will generally find the E2L the simpler fit. A team whose robot is built around a CAN FD network, with joints, sensors and other nodes sharing that bus, may prefer the E4L so the hand joins the existing architecture without a separate gateway. Where EtherCAT is the primary link, both variants offer it, and the choice of secondary interface becomes a matter of commissioning and diagnostics. Robots Middle East can review your control architecture before quotation and recommend the variant that suits it.

How does the RH56F1-E2L balance grip strength with fine force control?

The figures describe a hand that is firm without being blunt. The thumb delivers a fingertip force of at least 15N and each finger at least 10N, enough for secure grasps of tools, components and everyday objects. At the same time, force is resolved to 0.1N, which allows a controller to tighten or ease a grasp in small increments rather than switching between open and closed. Combined with a repeatability of ±0.2mm, this supports tasks where the same grasp must be reproduced across many cycles.

Speed completes the picture: the hand closes in 0.8s or less, and the 1 kHz communication frequency keeps the control loop tight while it does so. The all-metal body with its integrated skeleton underpins all of this, and it is also the reason the hand holds a static passive load of 30 kg. That figure deserves careful reading. A static passive load describes what the structure withstands when held in position, for example when supporting weight or being leant on; it is not an active lifting capacity. Applications that depend on lifting should therefore be discussed with our team before a configuration is fixed.

Who is the Inspire Dexterous Left Hand (RH56F1-E2L) for?

The hand suits several groups of buyers. University and institute laboratories working on grasping, teleoperation, imitation learning or human–robot interaction will value the combination of six degrees of freedom with fine force resolution, which provides a meaningful platform for manipulation research. Humanoid robot developers need left and right hands that behave consistently; for a matched pair, the natural partner is the Inspire Robots Dexterous Right Hand (RH56F1-E2R), which shares the EtherCAT and RS485 pairing. System integrators evaluating dexterous end-effectors for assembly, handling or inspection trials will find the robust metal construction and industrial bus well suited to pilot cells.

Teams whose research centres on touch itself should also consider the Inspire Dexterous Left Hand With Tactile Sensors (RH56F1-E2L-T1), the variant whose name indicates dedicated tactile sensing. Buyers comparing a broader selection of grippers and hands from several manufacturers can browse the Robot Hands category.

What is the Inspire Dexterous Left Hand (RH56F1-E2L) used for?

  1. Humanoid robotics: serving as the left end-effector of a bipedal or wheeled humanoid platform.
  2. Bimanual manipulation: holding, steadying and presenting objects while a right hand performs the main operation.
  3. Grasping research: studying grasp planning and force regulation on objects of differing shape and stiffness.
  4. Teleoperation and learning from demonstration: reproducing human hand motion captured by gloves or vision systems.
  5. Pilot automation cells: trialling dexterous handling of parts and tools before committing to production tooling.
  6. Teaching and training: giving engineering students practical experience of multi-joint hand control over industrial buses.

Pricing and Availability

Robots Middle East supplies the Inspire Dexterous Left Hand (RH56F1-E2L) on a quotation basis, so that the configuration, accessories and documentation match your project precisely. Please indicate whether you require a single left hand or a matched pair, which controller you intend to use, and whether mounting adapters, a power supply or cabling should be itemised in the order. Delivery, customs clearance and technical support are arranged together with your quotation. To begin, a quotation request for the Inspire Dexterous Left Hand (RH56F1-E2L) is available on this page.

Frequently Asked Questions

Is the RH56F1-E2L a left or a right hand?

It is a left hand. The corresponding right hand with the same interface pairing is the RH56F1-E2R.

Which communication interfaces does the RH56F1-E2L provide?

It provides EtherCAT and RS485, with a communication frequency of 1 kHz. If your system uses CAN FD, the RH56F1-E4L offers EtherCAT with CAN FD instead.

What operating voltage does the hand require?

The RH56F1 operates from 24V–48V. A power supply is not included unless it is itemised in the order.

What is included in the delivery?

One RH56F1 hand in the ordered configuration. Mounting adapters, a controller, a power supply and cables are supplied only when they are itemised in the order.

Can the hand lift 30 kg?

The 30 kg figure is the static passive load, which describes what the structure withstands when held in position, not an active lifting capacity. Our team will discuss lifting requirements with you before an order is placed.

How quickly does the hand close?

The hand closing time is 0.8s or less. Together with the 1 kHz communication frequency, this keeps grasping responsive in fast control loops.

Where can I buy the Inspire Dexterous Left Hand (RH56F1-E2L) and what does it cost?

You can buy it from Robots Middle East, which supplies customers across the Middle East. Pricing depends on the configuration and accessories you require and is provided in a formal quotation, which you can request from this page.

Summary

A dexterous hand earns its place in a robot through the quality of its conversation with the controller as much as through its strength. The Inspire Dexterous Left Hand (RH56F1-E2L) keeps that conversation fast and precise: EtherCAT and RS485 at 1 kHz, force resolved to 0.1N and positions repeated to ±0.2mm, all carried by an all-metal, integrated skeleton with six degrees of freedom and twelve joints. It suits laboratories, humanoid developers and integrators who need a capable left hand today and a consistent right-hand partner when the project grows. For a configuration agreed with Robots Middle East and supplied across the Middle East, this page is the starting point.

Specifications

General

BRAND INSPIRE ROBOTS
PART # RH56F1-E2L
ROBOT TYPE HAND

What's included

Inspire Dexterous Hand RH56F1-E2L (Left Hand Model) (RH56F1-E2L)

Product Questions

No questions yet. Be the first to ask.

0/255

Write a Review
You're reviewing: Inspire Dexterous Left Hand (RH56F1-E2L)
loader
Loading...

You submitted your review for moderation.